National Institute Of Materials Physics - Romania

In order to find solutions to current worldwide environmental problems, it is crucial to develop sustainable nanomaterials, ideally with multifunctional properties. Considering this, novel TiO2-SnO2@NMs (noble metals: Au and Ag) composites, for use as sustainable nanomaterials, were successfully prepared via a two-step synthesis process consisting of laser pyrolysis followed by the chemical impregnation of the collected materials with noble metals. The addition of SnO2 favors the transformation of TiO2 from a mixture with a majority Anatase phase to one with a Rutile phase majority. With consideration for their level of environmental toxicity, the features of the synthesized nanomaterials were structurally, morphologically, and optically described and assessed for environmental protection applications as gas sensors and photocatalysts. In the case of the Surface Acoustic Wave sensor, based on a pure TiO2 nanopowder, a notable difference in the frequency shift was detected in comparison to the other examined sensors. All sensors responded to the CH4 concentrations tested (0.02-0.1%). On the other hand, when methyl orange was photodegraded under visible light, the results obtained using NMs for decoration revealed that the photocatalytic activity of TiO2-SnO2@NMs was significantly improved compared to the TiO2-SnO2 binary composite, which already has an enhanced photocatalytic activity, compared to pure TiO2. Overall, this work produces nanoparticles that exhibit better sensory and photocatalytic features, as well as higher levels of biocompatibility with skin cells, for use as eco-friendly nanomaterials for a sustainable future.

Tungsten is the primary candidate armour material for the divertor target of the European demonstration fusion power plant. During operation at high temperature, pure tungsten is subject to fracture and recrystallization which results in a loss of strength and worsening of the thermal properties. Additionally, loss-of-coolant accidents with simultaneous air ingress can generate volatile and radioactive tungsten oxides. Advanced W-alloys were developed as alternative and upgrading armour materials of pure tungsten, such as potassium-doped tungsten laminates and self-passivating tungsten alloys. Three mock-ups were manufactured using potassium-doped tungsten laminates, W-10Cr-0.5Y and W-10Cr-0.5Y-0.5Zr as armour materials, each of them consisting of n degrees 4 blocks. The fabrication required optimization and upscaling of the ITER-like process which foresees oxygen-free high conductivity copper as interlayer joined to W-alloy armour block and CuCrZr ITER grade pipe welded to the Cu/W-alloy blocks by hot radial pressing. For quality control of the fabrication steps, non-destructive examination by ultrasonic testing was done on the monoblocks as received, after casting, after hot radial pressing and after high heat flux testing. The results demonstrated that these W-alloys can be used as armour materials of the European demonstration fusion power plant divertor target.

Quantum electrodynamical density functional theory is applied to obtain the electronic density, spin polarization, as well as orbital and spin magnetizations of square periodic arrays of quantum dots or antidots subjected to the influence of a far-infrared cavity photon field. A gradient-based exchange-correlation functional adapted to a 2D electron gas in a transverse homogeneous magnetic field is used in the theoretical framework and calculations. The obtained results predict a non-trivial effect of the cavity field on the electron distribution in the unit cell of the superlattice, as well as on the orbital and spin magnetizations. The number of electrons per unit cell of the superlattice is shown to play a crucial role in the modification of the magnetization via the electron-photon coupling. The calculations show that cavity photons strengthen the diamagnetic effect in the quantum dot structure, while they weaken the paramagnetic effect in the antidot structure. As the number of electrons per unit cell of the lattice increases, the electron-photon interaction reduces the exchange forces that will otherwise promote strong spin splitting for both the dot and the antidot arrays. Electronic density, spin polarization, as well as orbital and spin magnetizations of square periodic arrays of quantum dots or antidots subjected to the influence of a far-infrared cavity photon field are obtained using quantum electrodynamical density functional theory adapted to a 2D electron gas in a transverse homogeneous magnetic field. image

In this work, the formation of the orthorhombic phase of ZrO2 together with the minor monoclinic phase were elucidated by X-ray diffraction and transmission electron microscopy. Moreover, oxidized W can be responsible for the formation of oxygen vacancies in the ZrO2 through oxygen scavenging. The ferroelectric properties of the W/ZrO2/W film capacitors were investigated through piezoresponse force microscopy (PFM) and polarizationvoltage measurements. A second-order phase transition from the polar orthorhombic phase to the non-polar tetragonal phase was observed. Density functional theory calculations confirm our experimental results and propose that oxygen vacancies are responsible for the Curie-Weiss temperature of 130 degrees C, significantly lower than the theoretical value for the bulk.

The development of new materials for short-wavelength infrared (SWIR) optical sensors is of high importance for the fast development of different applications, as, for example, Internet of Things, road safety, and pollution monitoring. Group IV SiGe provides more sustainable As-, Cd-, and Pb-free nanomaterials that are cheaper and ecologic and offer easy integration with CMOS technology. This Review is on Ge and SiGe quantum dots/nanocrystals (QDs/NCs) embedded in dielectrics for VIS-SWIR photodetection, in which we highlight and discuss photocurrent mechanisms, correlation of photodetection parameters and characteristics with crystalline structure, morphology and energy bandgap, and applications as photodetectors, optical sensors, phototransistors, and solar cells. The embedding matrix induces NC surface passivation, stress field, and nanocrystallization effects and brings specific advantages depending on the matrix material. SiGe NCs in oxides for VIS-SWIR sensing represents a niche domain, showing high photosensitivity (photocurrent) in SWIR up to 1.8 mu m at room temperature and 2 mu m at 100 K, deeper in SWIR than Ge. By alloying Ge with a small content of Si, NC thermal stability is much improved as the detrimental Ge fast diffusion in oxides is hindered and SWIR photosensing is enhanced due to light absorption in Ge-rich SiGe NCs.

Magnesium ions, MgO nanoparticles and thin films, magnesium alloys and cerium compounds are materials intensively studied due to their corrosion protection, antibacterial and pharmacological properties. In this work, we have designed, prepared and investigated, novel thin films of MgO doped with cerium, deposited on Mg alloy (AZ31) for temporary implants, in order to enhance their life time. More precisely, we report on microstructure and corrosion behavior of MgO pure and doped with 0.1 at % Ce films, fabricated by sol-gel route coupled with spin-coating technique, on AZ31 alloy substrate. A modified sol-gel method that start from magnesium acetylacetonate, cerium nitrate and 2-methoxyethanol (as a stabilizer for the sol) was been used successfully for cerium doped MgO sol precursor preparation. The structure and morphology of the surface of the coatings, before and after immersion for 7-30 d in Hank's solution at 37 degrees C, were characterized by x-ray diffraction (XRD), scanning electron microscopy, high-resolution transmission electron microscope, x-ray photoelectron spectroscopy and Fourier infrared transmittance spectrum (FT-IR). A comparison between the corrosion protection of undoped MgO and MgO doped with 0.1 at % Ce coatings on the AZ31 alloy substrate is performed by electrochemical tests and immersion tests using open circuit potential and electrochemical impedance spectroscopy in Hank's solution, at 37 degrees C. The electrochemical results showed that the protection of the AZ31 alloy substrate against corrosion was better with the doped with 0.1 at % Ce MgO film deposited than with pure MgO coting. The investigations of the films after immersion in Hank's solution, at 37 degrees C, for 7, 21 and 30 d indicated that the grown layer on the film is bone like apatite that suggests a good bioactivity of 0.1 at % Ce-doped MgO coating. Our work demonstrates that the performance corrosion protection of the biodegradable magnesium alloys used for orthopedic applications, in simulated physiological environments (Hank and Ringer) can be enhanced through coating with Ce3+ doped MgO sol-gel thin film.

The CuFeTaTiW multicomponent alloy has been devised as an interlayer thermal barrier in nuclear fusion re-actors. In order to predict the phase constitution of this alloy, two different lines of work were performed: (a) simulation using Molecular dynamics and Monte Carlo and (b) study of the influence of mechanical alloying parameters on the structures formed. The simulation results show that the most stable structure is achieved starting from a bcc type-structure and using Monte Carlo simulation. In fact, in these conditions the separation into two bcc phases Fe-Ta-W and Cu-Ti is predicted at room temperature. However, the experimental preparation of the materials with mechanical alloying revealed that from 2 h of milling a single bcc phase is formed. The structure of the milled powder was not much influenced by the amount of the process control agent and the by the size of the W starting particles, but generally there was formation of Ta2H from the reaction between the powders and the process control agent.

The development of new materials for short-wavelength infrared (SWIR) optical sensors is of high importance for the fast development of different applications, as, for example, Internet of Things, road safety, and pollution monitoring. Group IV SiGe provides more sustainable As-, Cd-, and Pb-free nanomaterials that are cheaper and ecologic and offer easy integration with CMOS technology. This Review is on Ge and SiGe quantum dots/nanocrystals (QDs/NCs) embedded in dielectrics for VIS-SWIR photodetection, in which we highlight and discuss photocurrent mechanisms, correlation of photodetection parameters and characteristics with crystalline structure, morphology and energy bandgap, and applications as photodetectors, optical sensors, phototransistors, and solar cells. The embedding matrix induces NC surface passivation, stress field, and nanocrystallization effects and brings specific advantages depending on the matrix material. SiGe NCs in oxides for VIS-SWIR sensing represents a niche domain, showing high photosensitivity (photocurrent) in SWIR up to 1.8 mu m at room temperature and 2 mu m at 100 K, deeper in SWIR than Ge. By alloying Ge with a small content of Si, NC thermal stability is much improved as the detrimental Ge fast diffusion in oxides is hindered and SWIR photosensing is enhanced due to light absorption in Ge-rich SiGe NCs.

Preparation under non-identical conditions involving the reduction of sol-gel-derived precursors of various Zn:Fe atomic ratios (0.97:0.03, 0.8:0.2 and 0.4:0.6) in a hydrogen-containing atmosphere was used to obtain composites of nanosized ferromagnetic (FM) alpha-Fe and antiferromagnetic (AFM) FeO in different concentrations and of the desired magnetic responses. ZnO nanoparticles, developed in all preparation stages, served primarily as a matrix for the separation of Fe (and FeO) nanoparticles, preventing their agglomeration and coarsening. The average crystallite/particle size is about 5-32 nm, 10-75 nm and 21-31 nm for FeO, Fe and ZnO, respectively. Magnetisation investigations of FeO-Fe-ZnO nanocomposites revealed a coexistence of ferromagnetic and superparamagnetic behaviours ascribed to the Fe nanoparticles in different magnetic states. All samples exhibit the exchange bias effect, EB. Values up to 375 Oe for coercivity at 300 K, 600 Oe for coercivity, 223 for coercivity enhancement and 243 Oe for EB field at 5 K were measured. The magnitude of EB depends on the processing conditions - the EB field and coercivity enhancement are larger for samples processed under conditions of a higher degree of non-equilibrium. The presence of FeO appears crucial for the occurrence of EB, irrespective of its quantity. The EB is ascribed primarily to the exchange coupling between the AFM and FM spins at the FeO/Fe interfaces of nanostructures after field-cooling from above the TN of FeO and below the Curie temperature of Fe. An approach based on magnetically disordered AFM/FM interfaces featuring like spin-glass systems was adopted to explain the EB effects. An aspect of practical relevance is the suppression of room temperature coercivity in apparent correlation with the training of the EB; an attempt has been made to understand the origin of this suppression.

In the quest for advanced materials suitable for next-generation electronic and optoelectronic applications, tungsten disulfide (WS2) ultrathin films have emerged as promising candidates due to their unique properties. However, obtaining WS2 directly on the desired substrate, eliminating the need for transfer, which produces additional defects, poses many challenges. This paper aims to explore the synthesis of WS2 ultrathin films via physical vapor deposition (PVD) followed by sulfurization in a confined space, addressing the challenge of film formation for practical applications. Precursor layers of tungsten and WS2 were deposited by RF magnetron sputtering. Subsequent sulfurization treatments were conducted in a small, closed, graphite box to produce WS2 films. The physical and chemical properties of these precursor and sulfurized layers were thoroughly characterized using techniques such as X-ray reflectometry (XRR), X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The findings reveal notable distinctions in film thickness, structural orientation, and chemical composition, attributable to the different precursor used. Particularly, the sulfurized layers from the tungsten precursor exhibited a preferred orientation of WS2 crystallites with their (00L) planes parallel to the substrate surface, along with a deviation from parallelism in a small angular range. This study highlights the necessity of precise control over deposition and sulfurization parameters to tailor the properties of WS2 films for specific technological applications.